Garage Door Insulation: R-Values, Kits and Sealing the Gaps
A bare steel garage door hardly insulates at all: Clopay puts non-insulated doors at R-0 to R-2. Garage door insulation raises that to around R-6 with polystyrene and up to R-20 with polyurethane, and a retrofit kit adds about R-5 (foam board) to R-8 (fiberglass) to a bare door. Those ratings are for the insulation in one section; the whole door, joints and edges included, is rated by a tested U-factor. The first step matters most: insulated doors with tested U-factors lose a third to an eighth as much heat through the door as bare steel. Seal the gaps too, because air leaking around the door is a separate loss.
Insulating the garage door makes a garage warmer in winter, quieter and easier to heat. This guide gives the R-values of bare doors, insulated doors and kits, shows how much heat each kind of door lets through, and covers the two things that matter as much as the insulation: the door’s weight and the gaps around it.
R-values: bare doors, insulated doors and kits
An R-value measures how well a layer resists heat flow: the higher, the better. Here is what each kind of door, or door plus kit, is rated:
| Door or kit | R-value | Source |
|---|---|---|
| Single-layer steel or aluminum, no insulation | R-0 to R-2 | Clopay |
| Bare steel, by DASMA’s method: two air films, steel counted as zero | R-0.85 | DASMA TDS 163 |
| Insulated door, polystyrene core | R-6 to R-9, typically | Clopay |
| Insulated door, polyurethane core | R-6.3 to R-20.4, by model | Clopay |
| Foam board kit (EPS), 1¼ in thick | about R-5 | Cellofoam: R-4.0 per inch |
| Fiberglass kit with vinyl facing, 2¼ in thick | R-8 | Owens Corning |
The foam board kit’s R-value is our arithmetic: Cellofoam’s 4.0 per inch × 1¼ in. Kit R-values are for the insulation alone, measured on the material (ASTM C177 for Owens Corning’s). As with any door, the joints and edges lower what the whole door achieves, and gaps around it add air leaks on top.
R-value or U-factor?
Door makers quote two different numbers, and DASMA, the door and opener makers’ association, explains the difference in its data sheet on U-factor and R-value. An R-value is calculated for the middle of one door section. It leaves out the joints between sections, the edges and the hardware, which act as “thermal shortcuts” around the insulation. A U-factor comes from testing a whole door in a lab, so it includes those thermal bridges through the joints, edges and hardware. It doesn’t include air leaking through the gaps: DASMA’s verification program leaves air infiltration out, and doors are tested for it separately. Lower is better: DASMA notes that a door with a U-factor of 0.20 is twice as efficient as one at 0.40, and building codes use the U-factor. The two numbers are not reciprocals of each other, so compare doors on the same one. When a maker publishes a tested U-factor, use it.
How much garage door insulation saves
The heat a whole door lets through is its area × its U-factor × the temperature difference, in BTU per hour. A 16 × 7 ft door is 112 square feet. On a 10 °F night with the garage kept at 60 °F, a 50 °F difference:
- Bare steel, about U-1.18: 112 × 1.18 × 50 = about 6,600 BTU per hour. No tested U-factor is published for bare doors, so this is our estimate from DASMA’s calculation, which credits bare steel with nothing but the films of air on its two faces, R-0.85 in all.
- Polystyrene, tested at U-0.38 (Midland’s Series 24, 1⅞ in thick): 112 × 0.38 × 50 = about 2,100 BTU per hour, a third of the bare door.
- Polyurethane, tested at U-0.15 (Wayne Dalton’s Model 8350): 112 × 0.15 × 50 = 840 BTU per hour, an eighth of the bare door.
Wayne Dalton gives the same door a calculated section R-value of 12.12. Worked out from that, it would lose only about 460 BTU per hour (112 × 50 ÷ 12.12), about half its tested figure: the rest goes through the joints, edges and hardware. So compare insulated doors by their tested U-factors, which the makers in DASMA’s verification program publish and ICC-ES lists. Most of the gain still comes from the first step, from bare steel to an insulated door. Air leaking around the door comes on top of all these figures.
In the whole garage, the door is only one of five losses. Figure 1 adds them up for a 24 × 24 ft garage, the same way our garage heater size calculator does.
Two things stand out. Once the door is insulated, air leaks become the biggest single loss in this example, so sealing the gaps around the door can be worth more than a better door. And going from the U-0.38 door to the U-0.15 one saves about 1,300 BTU per hour here, about 9% of the total.
Is it worth it for your garage?
Clopay’s buying guide suggests an R-value of 10 to 13 for attached garages or cold climates, 15 or more for extreme climates, and 6 to 10 for a detached garage or a mild climate. It gives the reasons to insulate as comfort, lower heating and cooling bills, a quieter door and better dent resistance, and notes that a non-insulated door can make sense in a mild climate or a garage used only for parking. Insulation slows heat flow both ways, so it also helps keep a garage cooler in summer.
If you are replacing the whole door rather than adding a kit, compare garage door types and materials to understand the frame, facing, backing and glazing offered by each model.
Insulation kits: foam board, fiberglass and reflective
A kit fits a bare, single-layer steel door: the kind with open steel channels you can see from inside. A door with a foam core between two steel skins is already insulated.
- Foam board (expanded polystyrene, EPS). Cellofoam’s kit has eight pieces 1¼ in thick, 20 in wide and 4½ ft long, about 60 square feet, which it says is enough for a typical 9 ft wide door. Plymouth Foam’s kit is similar: eight 1¼ × 20 × 54 in panels for an 8 or 9 ft single door, and two kits for a 16 or 18 ft double door. In Cellofoam’s steps, each sheet is cut to the length between the door’s vertical rails, slipped in between the horizontal rails, and its ends tucked behind the vertical ones. Cellofoam’s sheet warns that the foam is combustible and should not be left exposed or unprotected.
- Fiberglass with a vinyl face. Owens Corning’s kit has eight R-8 panels, 2¼ in thick, with a washable white vinyl facing, held by adhesive fasteners and clips. One kit covers a single door up to 9 ft wide and 7 ft 4 in high, with each panel covering a pan up to 22 × 54 in. Owens Corning says the kit performs five times better than an uninsulated door.
- Reflective (foil) panels. Clopay notes that fiberglass and radiant barrier panels exist but are less common on garage doors and generally don’t match a polyurethane core.
A kit insulates the panels only. The joints between sections stay as they were, and DASMA counts such parts as thermal shortcuts around the insulation. Gaps around the door leak air, a separate loss that only seals reduce. A factory-insulated door has its core sealed between two skins, and some come with a tested U-factor. If the door is old, dented or drafty, compare a kit plus new seals with a new insulated door.
Check the weight and balance first
Insulation adds weight, and a garage door is balanced by springs made for its original weight. DASMA’s data sheet on adding weight to a garage door says extra weight can unbalance the door, damage or break the springs and overwork the opener, and it strongly advises against attaching materials to a door without explicit instructions from the door’s manufacturer. Added weight can also void the door’s warranty. Clopay’s guide adds that a heavier door may need a more powerful opener.
A foam kit is light but not weightless: Plymouth Foam lists its single-door kit at about 9½ lb, so about 19 lb for a double door with two kits. Before and after insulating:
- Ask the door’s maker whether a kit is allowed on your model.
- Test the balance. A balanced door stays put when you stop it partly open, says the U.S. Consumer Product Safety Commission. The full test is in our garage door maintenance checklist.
- If it drifts, call a trained door technician. Adjusting the springs is not a do-it-yourself job. DASMA notes that a technician can weigh the door on a scale, with the springs disabled, to check that they still suit it.
Seal the gaps
A door has three kinds of seals. DASMA’s garage door terminology sheet gives their trade names:
- Bottom seal, or astragal: the compressible strip on the bottom edge, held in a channel called the astragal retainer. It seals the door against the floor.
- Stop molding on the sides and top: trim usually nailed to the jambs outside the door, which seals the door’s edges against weather and light. A header seal can close the gap at the top.
- Seals between the sections: a weather seal at the joints, which DASMA calls a meeting rail seal. On the most efficient insulated doors, the joint also has a thermal break, a non-metal separation between the inner and outer skins (DASMA TDS 196).
Replacing the bottom seal
Bottom seals aren’t universal. Clopay’s weather seal instructions show two of its retainers: a bulb-shaped (“O”) channel on its single-layer steel doors and a “U”-shaped one on its insulated sandwich doors. Both hold the seal by T-shaped edges that slide along slots. Since retainers vary, Clopay says to ask the door’s maker for the matching seal. For the length, measure the door’s width: Clopay leaves 2 extra inches at the end and tucks them in to allow for the seal shrinking later.
Clopay’s steps start by disconnecting the opener, then clamping the open door in its tracks so it can’t move while the old seal slides out. Soapy water helps the new one slide in. For floors that aren’t level, Clopay says a special bottom seal may be available.
Water and drafts under the door
DASMA’s sheet on water under the door says rain getting past the bottom edge is common. Its fixes are built into the floor: a sill sloping 3° to 5° that the door rests on, or a notch in the edge of the slab, below the floor, that the bottom of the door closes into.
Whatever seal you fit, the door must still close fully onto the floor. DASMA says gaps between the door and the floor stop the safety reverse from working properly across the width of the door. After changing a bottom seal, check the safety reverse: the door must reverse when it touches a 2 × 4 laid flat on the floor, the monthly test that federal rules (16 CFR 1211) require opener manuals to give.
Two winter surprises: condensation and bowing
- Water droplets on the door. DASMA’s sheet on condensation says it isn’t normally a defect but the result of a warm, humid garage against a cold door. A wet or snow-covered car adds humidity. DASMA suggests ventilating the garage, keeping it cooler in extreme cold, and keeping the seals tight.
- A door that bows. Insulated doors made of two skins bonded to a foam core bow toward the warmer side. DASMA’s sheet on thermal bowing says a heated garage in a cold winter can make the door bow inward, which can open a gap at the top. It isn’t a defect; reinforcing struts across the back reduce it. Ask the door’s maker which ones fit.
Questions people ask
Does insulating a garage door help?
Yes, most of all if the garage is attached, heated or used as a workshop or gym. A bare steel door is near R-0 (Clopay); an insulated one starts around R-6. In our 24 × 24 ft garage example, an insulated door cuts the estimated heat loss by about a quarter with a U-0.38 door and nearly a third with a U-0.15 one. It also makes the door quieter, and it helps in summer too.
What R-value should a garage door have?
Clopay suggests R-10 to R-13 for an attached garage or a cold climate, R-15 or more in extreme climates, and R-6 to R-10 for a detached garage or a mild climate. If the maker gives a tested U-factor, compare that instead: lower is better (DASMA).
Are garage door insulation kits worth it?
On a bare, single-layer steel door, usually yes: a kit adds about R-5 (foam board) to R-8 (fiberglass) to panels that have almost none. The joints stay as they were, so the whole door gains less than the kit’s rating suggests. Check that the door’s maker allows it, and test the door’s balance afterwards, because the kit adds weight.
What is the best insulation for a garage door?
In a new door, a polyurethane core: Clopay’s reach R-20.4, against R-6 to R-9 for typical polystyrene doors. Between two doors, compare their tested U-factors where the makers publish them. For a retrofit kit, Owens Corning’s 2¼ in fiberglass panels are rated R-8, and 1¼ in EPS foam board about R-5 (R-4.0 per inch, Cellofoam).
Will insulation make my garage door too heavy?
It can. The springs are matched to the door’s original weight, and DASMA warns that added weight can unbalance the door and strain the springs and opener. A foam kit for a single door weighs about 9½ lb (Plymouth Foam). If the door no longer stays put when stopped halfway, have a trained technician check the springs.
What kind of bottom seal do I need?
The one that fits your door’s retainer, the channel on the bottom edge. Clopay alone uses bulb-shaped and U-shaped retainers on different doors, so take the door’s make and model, or a piece of the old seal, to the maker or a dealer. Buy a little more than the door’s width: Clopay leaves 2 in extra.
Can you insulate an insulated garage door more?
Not with a kit: the kits fit into the open pans of single-layer steel doors. On an insulated door, the gains left are at the seals: the bottom seal, the stop molding at the sides and top, and the joints.
More on doors: garage door sizes, what size garage door opener and the garage door maintenance checklist.
Sources
- DASMA, TDS 163, U-factor and R-value for Residential and Commercial Garage Doors (rev. July 2022): calculated section R-value, air films of R-0.85, steel facings counted as negligible, tested U-factor per ANSI/DASMA 105
- DASMA, TDS 196, U-factor on Garage Doors and the DASMA Thermal Performance Verification Program: lower U-factor is better, 0.20 versus 0.40, the IECC test method; the test covers the sections, joints, hardware and perimeter, and the program leaves out air infiltration
- ICC Evaluation Service, DASMA thermal performance verification listings TPVP-101 (Midland Garage Door, reissued May 2026: Series 24, 1.88 in polystyrene, U-0.38) and TPVP-102 (Wayne Dalton, reissued March 2026: Model 8350, polyurethane, U-0.15), tested to ANSI/DASMA 105; Wayne Dalton, Model 8350 brochure (2024): calculated section R-value 12.12 (read October 22, 2026)
- Clopay, Technically Speaking: Thermal Properties: what the U-factor test includes, and air infiltration tested separately under DASMA 105 (read October 22, 2026)
- DASMA, TDS 176, Adding Weight to a Garage Door Assembly, and TDS 190, Factors Affecting Spring Cycle Life: added weight, balance, springs and opener
- DASMA, TDS 160, Sectional Garage Door Terminology: astragal, astragal retainer, stop mould, header seal, thermal break
- DASMA, TDS 197, Water Infiltration Under the Bottom of a Sectional Door; TDS 369: gaps under the door and the reversing system
- DASMA, TDS 195, Garage Doors and Condensation, and TDS 185, Thermal Bowing of Garage Doors with Bonded Core Sections
- Clopay, insulated vs. non-insulated garage doors and guide to insulated garage doors: door R-values, added weight, recommended R-values by climate
- Clopay, installation instructions for bulb- and U-shaped bottom seals
- Owens Corning, Garage Door Insulation Kit: R-8 fiberglass panels, sizes and coverage
- Cellofoam, garage door insulation kit sheet (EPS, R-4.0 per inch, combustibility warning); Plymouth Foam, garage door insulation kit sheet (panel sizes, kit weight)
- U.S. Consumer Product Safety Commission, Non-Reversing Automatic Garage Door Openers Are a Hazard (Pub. 523): a balanced door; and 16 CFR 1211, the monthly reverse test (all read October 20, 2026)